NetBSD/cobalt on COBALT Cache RaQ 2

COBALT Cache RaQ 2で、NetBSD 6辺りが起動しないこともあったけれど、2023年12月ぐらいのcurrentは動いてます。

    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 10.99.10 (GENERIC) #1: Mon Dec 11 21:32:57 JST 2023
        root@st9201.kankyo-u.ac.jp:/home/nakaji/current/obj.cobalt/sys/arch/cobalt/compile/GENERIC
Cobalt RaQ 2
total memory = 256 MB
avail memory = 246 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a, 32-byte FIFO
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev. 10.0
cpu0: 48 TLB entries, 16MB max page size
cpu0: 32KB/32B 2-way set-associative L1 instruction cache
cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
lcdpanel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:00:6f:33
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, UHCI, revision 0x02) at pci0 dev 9 function 2 not configured
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:00:6f:32
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
timecounter: Timecounter "mips3_cp0_counter" frequency 125000000 Hz quality 100
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
WARNING: system needs entropy for security; see entropy(7)
wd0 at atabus0 drive 0
wd0: <ST380021A>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
swwdog0: software watchdog initialized
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/cobalt/10.99.10/modules
entropy: best effort
entropy: ready