Cisco300 - 180知識点を覚えていますか

2018年9月8日 18:03

きっと多くの人がこんなことをしたことがある。自分が300-180勉強をしているときには、すでにある知識について理解と把握ができているような気がします。しかし、この知識点については、後日、自分の頭の中の空白を発見しました。これは300 - 180知識点を覚えていないということです。つまり、私たちはこの知識に対して本当に身につけていることはありません。

300-180 DCIT
Troubleshooting Cisco Data Center Infrastructure (DCIT)
試験番号 300-180 DCIT
関連資格 CCNP Data Center
試験時間 90 分（70 ～ 80 問）
試験言語英語
試験登録 Pearson VUE

300-180 Troubleshooting Cisco Data Center Infrastructure（DCIT）試験は、CCNP Data Center 認定に関連する試験の 1 つです。この試験では、シスコのデータセンターインフラストラクチャのトラブルシューティングに関する知識が問われます。試験には、データネットワークプロトコル、ネットワークの仮想化と自動化、アプリケーションセントリックインフラストラクチャ（ACI）、ストレージ、コンピューティングプラットフォーム、管理と運用が含まれます。この試験の出題内容に合わせたトレーニングには、Troubleshooting Cisco Data Center Infrastructure v6（DCIT）コースがあります。

300 - 180のある知識点の学習に対して、私たちはその定義、どのように適用し、どのようにこの知識によって別の知識点を出すかをはっきりさせるべきである。このようにして、私達はこの300 - 180の知識点に対してもっと全面的な認識があることができます。この点では、ITshiken 300 - 180問題集は良い選択かもしれません。300 - 180問題集は私たちに欠片化時間の利用を実現させることができるので、私たちにとって300 - 180の記憶に役立ちます。

Question No : 1
Topic 1, Questions Set 1

A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however, the boot fails.
What is the cause of this failure?
A.The local disk must be the first device in the boot order.
B.eUSB is not a supported boot device.
C.eUSB support is available only on the Cisco UCS C-Series rack server.
D.eUSB is not the first device in the boot order for the server.

正解: D

Question No : 2
A customer is troubleshooting degraded DIMM errors on a Cisco UCS blade server and would like to reset the BMC.
What is the correct command sequence to reset the BMC?
A.UCS1-A# server x/y UCS1-A /chassis/server # scope bmc UCS1-A /chassis/server/bmc # reset UCS1-A /chassis/server/bmc* # commit-buffer
B.UCS1-A# server scope UCS1-A /chassis/server # scope bmc UCS1-A /chassis/server/bmc # reset UCS1-A /chassis/server/bmc* # commit-buffer
C.UCS1-A# scope server x/y UCS1-A /chassis/server # scope bmc UCS1-A /chassis/server/bmc # reset UCS1-A /chassis/server/bmc* # commit-buffer
D.UCS1-A# scope server x/y UCS1-A /chassis/server # scope bmc UCS1-A /chassis/server/bmc* # commit-buffer

正解: C

Question No : 3
Which commands can you enter to see if a component in the Cisco UCS domain generated a core file?
A.6100-A# scope monitoring 6100-A /monitoring # scope sysdebug 6100-A /monitoring/sysdebug # show cores Core Files: Name Fabric ID ---------- ---------
B.6100-A# scope sysdebug 6100-A /sysdebug # scope monitoring 6100-A /sysdebug/monitoring # show cores Core Files: Name Fabric ID ---------- ---------
C.6100-A# scope system 6100-A /system # scope monitoring 6100-A /system/monitoring # show cores Core Files: Name Fabric ID ---------- ---------
D.6100-A# scope cores 6100-A /cores # show cores Core Files: Name Fabric ID ---------- ---------
E.6100-A# scope logging 6100-A /logging # scope monitoring 6100-A /logging/monitoring # show cores Core Files: Name Fabric ID ---------- ---------

正解: A

Question No : 4
Which four tech support files can you create with the Cisco UCS Manager that you can submit to Cisco TAC for support? (Choose four.)
A.UCSM
B.disk LUNs
C.fabric extender
D.memory
E.rack server
F.chassis
G.server cache

正解: ACEF

Question No : 5
Which protocols can be used to send to Cisco TAC (Technical Assistance Center) the show tech-support command output information about the Cisco UCS domain? (Choose two.)
A.TFTP
B.FTP
C.SCP
D.Telnet
E.SecureTelnet

正解: BC

Question No : 6
The Cisco UCS Manager displays FSM information for which four of these? (Choose four.)
A.which FSM task is being executed
B.the current state of an FSM task
C.the status of the previous FSM task
D.any error codes returned while processing
E.all completed FSM tasks
F.multiple FSM tasks that completed over multiple tries
G.multiple FSM tasks that failed

正解: ABCD

Question No : 7
How will the Cisco UCS Manager react when all of the FSM tasks fail?
A.retries for 60 seconds
B.raises faults and alarms
C.restarts from the previous known good task
D.sends an NOC SNMP trap email

正解: B

Question No : 8
What should you do when you see faults during the initial setup and discovery process?
A.Take note and address the faults.
B.You can safely ignore these faults.
C.Log them and try to address the first one.
D.Reboot until the error messages go away.

正解: B

Question No : 9
When using the Cisco UCS Manager GUI to troubleshoot a suspected bad memory, which logs contain data that are related to the faulty DIMM?
A.the System Event log and Faults log that are located under the Admin tab
B.the Events log and Faults log that are located under the Admin tab
C.the System Event log that is located under the Server tab in the Navigation panel and the Faults log that is located under the Admin tab
D.the System Event log that is located under the Equipment tab and the Faults log that is located under the Admin tab

正解: D

Question No : 10
Which three are valid tech support bundles to collect in the local management shell? (Choose three.)
A.UCSM
B.UCSM-MGMT
C.Port-Channel
D.Adapter
E.SAN
F.FEX

正解: ABF

Question No : 11
The Core File Exporter automatically exports cores to a remote server as they are generated.
Which protocol does it use for this action?
A.FTP
B.SCP
C.SFTP
D.TFTP

正解: D

Question No : 12
Which log file in Cisco UCS Manager contains information about which user took a specific action?
A.user access log
B.system change log
C.audit log
D.access control log

正解: C

Question No : 13
Which statement is true about system event logs?
A.By default, they require manual clearing.
B.They report operating system crashes and errors.
C.They are also referred to as system error logs.
D.They can only be accessed from Cisco UCS Manager.

Question No : 14
Which piece of information does the FSM provide?
A.the current task and status
B.a collection of blade statistics
C.the last user to access the resource
D.a list of faults currently suppressed by the Cisco UCS Manager

正解: A
Question No : 15
Which of these does not have an FSM associated with it?
A.vCenter connection
B.service profile
C.server hardware
D.service profile templates

正解: D